Delta Pulse 3 Montaj ve Çalıstırma Kılavuzu http:/// Bu kılavuz, montajı eksiksiz olarak yapılmış devrenin kontrolü ve çalıştırılması içindir. İçeriğinde montajı tamamlanmış devrede çalıştırma öncesinde yapılması gereken adımlar ve çalıştırma sırasında dikkat edilmesi gerekenler yer almaktadır. Dokümanın en altında eski versiyon PCB için montaj sırasında dikkat edilmesi gereken hususlar yer almaktadır. Montaj sırasında devrenizde kılavuza uygun olmayan durumlar oluştu ise forumdan(http:///yeni/index.php?topic=3797.0 ) bilgi alabilirsiniz. Devreye ait dokümanlar için lütfen sitemizi ziyaret ediniz. Ana Sayfa: http:///index1.html Forum Linki: http:///yeni/ İlgili Konu Linki: http:///yeni/index.php?topic=3797.0
Montaj Sırasında Dikkat Edilecek Hususlar(Eski PCB) Not: Bu kısım güncel PCB için geçerli değildir. Bu versiyon siteden kaldırılmıştır. Bu kısım önceden PCB basanlar içindir. 1. In the picture, the components circuled and number 1 (2n2907) should be rotated 180 degrees like in picture 2. In the picture, the component circled and number 2 (BS250) should be rotated 180 degrees like in the picture. 3. In the picture, the component circuled and numbed 3 can be replaced with transistor BC557. 4. Mosfet IRFU024 must be replaced with mosfet 2N7000 5. BT169D should be used as opposed to SCR. 6. C13 should be a Tantalum Capacitor
7. If you intend to use the charger circuit, the two red dots in the picture below must be bridged. consideration when assembling NEW PCB components The construction should be based on the diagrams provided, abiding to general rules. (Short circuits, drying of resins) General Notes: Information regarding LCD Winstar WG12864B Contrast resistors: 6,8K 2,2KLarge size LCD Information Winstar WG12864AContrast resistors: 8,2k 560R Bağlantı sıralaması:
checks to be made after assembly 1. Position the PCB like in the picture above 2. Ensure for the first version 2n2907 and bs250 are installed as in picture.
3. Next the whole circuit should be checked for 12v to ensure no shot circuits. ( NOTE, IM NOT SURE IF I TRANSLATED THIS PART CORRECTLY) 4. Now ground the probe and check to see if there is 12V battery supply like in the picture for the pin show in the picture.
5. Place you negative probe on the Gnd sine and measure all components as shown in the pictures above, they should show 5V. 6. Next make the connection like in the picture above.
7. Ground you negative probe to the - sine and ensure all components in the pictures above show 12v.
8. Ground your negative probe to the sine and ensure all components shown in the pictures above show + 1.6~1.8v. Next sentence on the same page says: all the above must be checked. all the above must be checked.
9. Now the PIC and LCD and all other components can be constructed as in the pictures above. 10. Looking at the picture above the Grd voltage should be checked to be between +6~7,5v (NOTE MAYE HAVE TRANSLATED THIS PART WRONG) If you have not encountered any problems you may now connect PIC and LCD
11- connect 6.2v to the D6 the 5th pin 12. The frequency should be measured here as show in the picture above to show 178~180HZ
13. The frequency should be measured here like in the picture should be 178~180HZ. The frequency here should be 178~180 HZ
15. The frequency measured here should be 178~180HZ
16-16. The frequency measured here should be 178~180hz If you follow all of these steps you should not encounter a problem. If a problem dose arises you may look at the forum (http:///yeni/i...p?topic=3797.0) to get the necessary information.