Conduits Elektrik Tesisat Borular Rf,tktghjdjls

Transkript

1 SECTION I Conduits Elektrik Tesisat Borular Rf,tktghjdjls EMT, IMC, RSC, Galvanized Steel Flexible, Liquidtight, PVC Schedule 40 & 0

2 GALVANIZED ELECTRICAL METALLIC TUBING (EMT) - STEEL General Steel Electrical Metallic Tubing is manufactured from mild steel tube. It has an accurate circular cross section, a uniform wall thickness, a defect free interior surface, and continuously welded seams. The exterior surface is thoroughly and evenly coated with zinc using an inline galvanizing process, so that metalto-metal contact and galvanic protection against corrosion are provided. Additionally, the exterior is protected by a clear zinc chromate coating. The interior surface is coated with organic lubricating coating to reduce friction during wire insertion and retard corrosion. EMT and its associated tubular fittings are produced in nominal trade sizes from 1/2 to 4. EMT is produced in standard lengths of 10 feet (3.05 m). Bundles of finished EMT are wrapped with color coded special light weight filament tape. Black tape identifies trade sizes 1/2 and 1 1/2, Red tape identifies 3/4 and 1 1/4, and Blue tape 1. Trade sizes 2 and larger are not bundled. EMT is a UL Listed product. Each length of tubing has a label affixed containing UL Listing information and a bar code. Each length is identified with name, Logo, the letters EMT clearly and durably marked once per 10 feet (3.05 m) length, a U.L. listing nmber and the words, Consult manufacturer for installation instructions. On July 25, 2001 the past UL requirement to embed the letters EMT into the surface of the tube was changed to require only durably marking the tube with the letters EMT at a minimum of 1/ inch (3 ) high. Trade Size 1/ 3/ 1 1/ 1 1/ 2 1/ 3 1/ Metric Designator Weight 10 Unit Lengths Galvanized Steel Electrical Metallic Tubing, National Electrical Code (NEC ) 200 Article 35, can be installed indoors or outdoors, in dry or wet locations, exposed or concealed, in all kinds of atmospheric conditions, and in hazardous locations, when in accordance with the NEC and providing it will not be suject to severe physical damage during and after installation and is properly protected against corrosion. Also, it provides mechanical protection for the conductors while reducing Electro-Magnetic Field (EMF) exposure and shielding against Electro-Magnetic Interference (EMI). Galvanized Steel Electrical Metallic Tubing is an approved equipment grounding conductor under the 200 NEC Section 250.(4). The NEC establishes the minimum requirements for a safe electrical installation. Because of the varied environments in which electrical equipment is installed, local amendments are often added. Always consult local codes prior to any installation. WEIGHTS AND DIMENSIONS Outside Diameter (1) Specifications Galvanized Steel Electrical Metallic Tubing is manufactured in accordance with the latest edition of the following: American National Standards Institute - American National Standard for Steel Electrical Metallic Tubing (EMT) ANSI C0.3 Underwriters Laboratories Standard for Electrical Metallic Tubing - Steel, UL 77. National Electrical Code Article 35. Federal Specification - WW-C-563 The above Federal specification may still be referenced, however the federal government has canceled it and adopted the UL 77 and ANSI C0.3 standard and will no longer maintain a separate Electrical Metallic Tubing was covered under WW-C-563. Additional information on the titles and designations of standards or requirements that have been used for the investigation of products in a specific category can be found in the Underwriters Laboratories Inc., General Information for Electrical Equipment Directory. The UL product category for EMT is FJMX. APPROVED BRANDS : E4675 E Wheatland Inside Diameter (2) Wall Thickness (2) lb kg Notes : Applicable tolerances Length : 10 Ft. (3.05 m) +/- 1/4 (+/ ) (1) Outside Diameter : 1/2-2 +/ ( / ) 2-1/2 +/ (63 +/ ) 3 +/ (7 +/- 0.3 ), 3-1/2-4 +/ ( / ). (2) For information only, not a UL 77 requirement A 01

3 D fis Z EMT GALVAN ZL ÇEL K BORULAR Genel kullan m amaçl, Amerikan U.L. onayl, NEC flartnamesine uygun elektrik tesisat borular d r. Özel alafl ml yüksek kaliteli çelikten imal edilmifl ve s cak dald rma yöntemiyle galvanizlenmifltir. Borular n standart uzunluklar 10 ft (3.05 m) dir. Borular diflsiz oldu u için montaj süratle gerçeklefltirilir. De iflik aksesuarlar ve bükme aparatlar yla flantiyede montaj esnas nda elle bükme yap labilir. Manflon, rakor ve di er fittingleri kullanmak için özel bir alet gerekmez. Borular n içi imalat esnas nda temizlenip kaygan bir madde ile kaplanm flt r. Kablolar kolayca ve izolasyona zarar vermeden çekilir. Diflsiz EMT borular kablolar sadece mekanik zarara karfl korumakla kalmaz ayn zamanda linyelerin elektromanyetik korumas da yapar. Aleve ve dumana karfl içten ve d fltan koruma sa layan en güvenli tesisat sistemidir. Diflsiz EMT çelik boru sistemi konutlarda, ifl ve al flverifl merkezlerinde, otellerde, kamu binalar nda, hastanelerde, okullarda ve benzeri yap larda güvenle kullan lmaktad r. Referans projelerimizden baz lar : fl Bankas Üç Kuleler, Garanti Bankas Genel Müdürlük Binas, Tekfen Tower ve Eczac bafl Kanyon Projesi. APPROVED BRANDS : E4675 E Wheatland ÜRÜN KODU EMT-050 EMT-075 EMT-100 EMT-125 EMT-150 EMT-200 EMT-250 EMT-300 EMT-350 EMT-400 ÖLÇÜ U.S / Metrik 1 / 3 / 1 1 / 1 1 / 2 1 / 3 1 / A IRLIK Adet / Kg. NOM NAL DIfi ÇAP MM. NOM NAL ET KALINLI I MM. STANDART BA ADED kg Adet kg Adet kg Adet kg Adet kg Adet kg Adet 63.0 kg Adet 7.3 kg Adet kg Adet kg Adet A 02

4 INTERMEDIATE METAL CONDUIT (IMC) - STEEL General Steel Intermediate Metal Conduit is manufactured from a mild steel tube. It has an accurate circular cross section, a uniform wall thickness, a defect free interior surface, and a continuous welded seam. To protect from corrosion the exterior surface is thoroughly and evenly coated with metallic zinc applied directly to the surface of the steel so that metalto-metal contact and galvanic protection against corrosion are provided. The interior surface is protected by an organic corrosion-resistant coating to which an additional lubricating coating is applied to reduce friction during wire insertion. IMC and its associated tubular fittings are produced in nominal trade sizes from 1/2 to 4. IMC produced in standard lengths of 10 feet (3.05 m), including coupling, is threaded on both ends, with a coupling applied to one end. A by size color-coded thread protector is applied to the other end, to aid in trade size identification. Galvanized Intermediate Metal Conduit, National Electrical Code (NEC ) 200 Article 342, can be installed indoors or outdoors, in dry or wet locations, exposed or concealed, in all kinds of atmospheric conditions, and in hazardous locations, when in accordance with the NEC 501.4, 502.4, 503.3, and Also, it provides excellent mechanical protection for the conductors while reducing Electro- Magnetic Field (EMF) exposure and shielding against Electro-Magnetic Interference (EMI). Specifications Galvanized Intermediate Metal Conduit is manufactured in accordance with the latest edition of the following: American National Standards Institute - American National Standard for Electrical Intermediate Metal Conduit (EIMC) ANSI C0.6 Underwriters Laboatories Standard for Electrical Intermediate Metal Conduit Steel, UL National Electrical Code Article 342. Federal Specification - WW-C-51 The above Federal specification may still be referenced, however the federal government has canceled it and adopted the UL 1242 standard and will no longer maintain a seperate standard. Intermediate Metal Conduit was covered under WW-C-51, Class 2, Tpe A. Yellow thread protectors represent trade sizes 1/2, 1-1/2, 2-1/2, 3-1/2, Green 3/4 and 1-1/4 trade sizes, and Orange full trade sizes 1, 2, 3, and 4. The finished threads, National Pipe Taper (NPT), conforms to the American National Standard for Pipe Threads, General Purpose (Inch), ANSI/ASME B The taper of threads is 3/4 inch per foot (1 in 16). Threads are treated with a protective coating to prevent corrosion before installation. Each length of conduit has a label affixed which contains the UL Listing and a bar code. Each length is identified with Wheatland s name, Logo, the product name Intermediate Metal Conduit or IMC, a U.L. listing number and the words, Consult manufacturer for installation instructions. Trade Size Metric Designator Threads Per Acceptable Length of Finished Counduit without Coupling Galvanized Ihtermediate Metal Conduit is an approved equipment grounding conductor, the 200 NEC Article 250.(3). The NEC establishes the minumum requirements for a safe electrical installation. Because of the varied environments in which electrical equipment is installed, local amendments are often added. Always consult local codes prior to any installation. WEIGHTS AND DIMENSIONS Weight 10 Unit Lengths with Couplings Outside Diameter (1) Additional Infonmation on the titles and designations of standards or requirements that have been used for the investigation of products in a specific category can be found in the Underwriters Laboratories Inc., General Information for Electrical Equipment Directory. The UL product category for Intermediate Ferrous Metal Conduit is DYBY. APPROVED BRANDS : E56 E Wheatland Inside Diameter (2) Wall Thickness (2) 1 / 3 / 1 1 / 1 1 / 2 1 / 3 1 / 4 1 / Inch /2 1/2 1/2 ft. (+/-/) 1/4 1/4 10 1/2 10 1/2 10 1/4 10 1/4 (+/- 6 ) Notes : (1) Figures are the average of the maximum and minimum dimensions as given in UL (2) Calculated from nominal outside diameter and nominal wall thickness. lb kg A 03 Steel Intermediate Metal Conduit is manufactured to the lengths shown above, so when a straight-tapped coupling is attached a 10 foot (3.05 m) lenght is produced.

5 GALVANIZED RIGID METAL CONDUIT (RSC) - STEEL General Rigid Steel Conduit is manfactured from mild steel tube. It has an accurate circular cross section, a uniform wall thickness, a defect free interior surface, and a continuous welded seam. The interior and exterior surfaces are throughly and evenly coated with zinc using the hotdip galvanizing process, so that metalto-metal contact and galvanic protection against corrosion are provided. A clear coating of zinc chromate is also applied. Additional lubricating coating may be applied to the interior surface to reduce friction during wire insertion. Galvanized Rigid Steel Conduit can be installed indoors or outdoors, in dry or wet locations, exposed or concealed, in all kinds of atmospheric conditions, and in hazardous locations when in accordance with the NEC Article 344. Also, it provides excellent mechanical protection for the conductors while reducing Electro-Magnetic Field (EMF) exposure and shielding against Electro- Magnetic Interference (EMI). Trade Sizes 2 through 6 ade UL Listed for use with directional boring equipment. Specifications Wheatland Galvanized Rigid Steel Conduit is manufactured in accordance with the latest edition of the following: American National Standards Institute - American National Standard for Electrical Rigid Steel Conduit (ERSC) ANSI C0.1 Underwriters Laboatories Standard for Electrical Rigid Steel Conduit - Steel, UL 6. National Electrical Code Article 344. RSC and its associated tubular fittings are produced in nominal trade sizes from 1/2 to 6. RSC produced in standard lengths of 10 feet (3.05 m), including coupling, is threaded on both ends, with a coupling applied to one end a by size color-coded thread protector to the other. Black thread protectors identify trade sizes 1/2, 1-1/2, 2-1/2, 3-1/2. Red 3/4 and 1-1/4. Blue thread protectors identify trade sizes 1, 2, 3,4,5, and 6. The pitch of threads conforms to the American National Standard for Pipe Threads, General Purpose (Inch), ANSI/ASME B The taper of threads is 3/4 inch per foot (1 in 16). Threads are protected after cutting by an application of molten zinc. Each length of conduit has a label affixed which contains the UL Listing and a bar code. Each length is identified with the words Rigid Steel Conduit, a U.L. listing number and the words, Consult manufacturer for installation instructions. Trade Size 1/ 3/ 1 1/ 1 1/ 2 1/ 3 1/ 5 6 Metric Designator Threads Per Inch /2 1/2 1/2 1/2 ft. Galvanized Rigid Steel Conduit is an approved equipment grounding conductor, 200 NEC Article 250.(2). The NEC establishes the minumum requirements for a safe electrical installation. Because of the varied environments in which electrical equipment is installed, local amendments are often added. Always consult local codes prior to any installation. Acceptable Length of Finished Counduit without Coupling (+/-1/4n.) 1/4 1/4 10 1/2 10 1/2 10 1/4 10 1/ WEIGHTS AND DIMENSIONS (+/- 6 ) Weight 10 Unit Lengths with Couplings lb Federal Specification - WW-C-51 The above Federal specification may still be referenced, however the federal government has canceled it and adopted the UL 6 standard and will no longer maintain a seperate standard. Rigid Steel Conduit was covered under WW-C-51, Class 1, Tpe A. Additional Infonmation on the titles and designations of standards or requirements that have been used for the investigation of products in a specific category can be found in the Underwriters Laboratories Inc., General Information for Electrical Equipment Directory. The UL product category for Rigid Ferrous Steel Conduit is DYIX. * For information only, not a UL 6 requirement. Rigid Steel Conduit is manufactured to the lengths, shown above, so when a straight-tapped coupling is attached a 10 foot (3.05 m) length is produced. Wheatland trade sizes 3 through 6 are UL Listed for use with directional boring equipment. kg Nominal Outside Diameter* APPROVED BRANDS : E22335 E Wheatland Nominal Inside Diameter* Nominal Wall Thickness* A 04

6 D fil IMC/RSC GALVAN ZL ÇEL K BORULAR Diflli IMC / RSC Galvanizli Çelik borular özellikle patlama tehlikesinin bulundu u a r hizmet tipi ortamlarda kullan lan, Amerikan U.L. onayl ve NEC flartnamesine uygun elektrik tesisat borular d r. Özel alafl ml, yüksek kaliteli çelikten imal edilmifl ve s cak dald rma yöntemiyle galvanizlenmifltir. Yüksek et kal nl ve konik difl sistemi sayesinde alevs zd rmazl k özelli ine sahip olan bu borular çok yüksek mekanik dirence karfl koyabilir. Borular n içi imalat esnas nda temizlendi i için kablolar kolayca ve izolasyona zarar vermeden çekilir. Diflli IMC / RSC Borular kablolar sadece mekanik zarara karfl korumakla kalmaz, ayn zamanda linyelerin elektromanyetik korumas n da yapar: Boru çap na uygun bükme aparatlar yla flantiyede montaj esnas nda elle bükme yap labilir. Uygun muf, rakor, tespit kroflesi ve di er tüm ba lant elemanlar stoklar m zda mevcut olan Diflli IMC / RSC Çelik borular, bir ucunda muf di er ucunda difl koruyucu plastik ile teslim edilmektedir. Diflli IMC Çelik Borular rafineriler, petrokimya tesisleri, boru hatlar dolum ve pompa istasyonlar, askeri üsler ve cephanelikler, havaalanlar, a r sanayi tesisleri ve benzeri patlama tehlikesi içeren yerlerde güvenle kullan lmaktad r. Referans projelerimizden baz lar : Bakü-Tiflis-Ceyhan Boru Hatt, Tüprafl, Tedafl, Band rma Gübre Fabrikas. APPROVED BRANDS : E22335 E Wheatland ÜRÜN KODU ÖLÇÜ U.S / Metrik A IRLIK Adet / Kg. NOM NAL DIfi ÇAP MM. NOM NAL ET KALINLI I MM. STANDART BA ADED IMC-050 1/ kg Adet IMC-075 3/ kg Adet IMC kg Adet IMC / kg Adet IMC / 41.0 kg Adet IMC kg Adet IMC / kg Adet IMC kg Adet IMC / kg Adet IMC kg Adet RSC kg Adet RSC kg Adet A 05

7 GALVANIZED FLEXIBLE STEEL CONDUITS / GALVAN Z KAPLI ÇEL K SP RAL BORULAR GALVANIZED FLEXIBLE STEEL CONDUIT / GALVAN Z KAPLI ÇEL K SP RAL BORU Arrowtite Galvanizli Çelik Spiral Borular bükülme özelli ine sahip, Amerikan U.L onayl, NEC flartnamesine uygun elektrik tesisat borular d r. Özel alafl ml yüksek kaliteli çelikten imal edilmifl ve s cak dald rma yöntemi ile galvanizlenmifltir. Diflsiz EMT Boru sistemi ile kullan lan Çelik Spiral Borular asma tavan alt armatür montaj ve bükülme özelli inin gerekli görüldü ü dahili uygulamalarda tercih edilmektedir. ÜRÜN ÖLÇÜ RULO MAKARA ORTALAMA BORU DIfi BORU Ç TAM BÜKÜLÜ A IRLIK/ KODU inches Metrik B R M B R M ÇAPI ÇAPI D RSEK ÇAPI 100feet (feet) (feet) (pounds) (min / max) (min / max) inches / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / Flexible metal raceway for electrical power, control and counication cables Motor leads Listed assemblies Listed wire fixtures Manufactured wiring systems Description Reduced Wall Flexible Steel Conduit High grade hot dipped zinc galvanized low carbon steel Interlocking design Corrosion resistant References & Ratings UL 1, UL 147, File Reference E31, CSA File Number 15035, CSA C22.2 No. 56 (trade size 3/ only) NEC 250.(6), (C), , 501.4(B)(2), Federal Specification WW-C566C, (now supeseded by UL 1) Cable Tray installations per NEC Environmental Air-Handling space installation NEC (C) UL Classified 1, 2 and 3 - hour Through-Penetration Fire Systems UL File R14141 GALVANIZED EXTRA FLEXIBLE STEEL CONDUIT / GALVAN Z KAPLI ÇEL K EXTRA FLEXIBLE SP RAL BORU Arrowtite Galvanizli Çelik Spiral Borular bükülme özelli ine sahip,elektrik tesisat borular d r. Özel alafl ml yüksek kaliteli çelikten imal edilmifl ve s cak dald rma yöntemi ile galvanizlenmifltir. Diflsiz EMT Boru sistemi ile kullan lan Çelik Spiral Borular asma tavan alt armatür montaj ve bükülme özelli inin gerekli görüldü ü dahili uygulamalarda tercih edilmektedir. ÖLÇÜ inches 1/ 3/ 1 1/ 1 1/ 2 1/ RULO B R M (metre) BORU DIfi ÇAPI (min / max) BORU Ç ÇAPI (min / max) / / / / / / / / / / / / / / / / / / Description Non-UL Extra Flexible Steel Conduit High grade galvanized low carbon steel Interlocking design Corrosion resistant TIS ISO 000 Flexible metal raceway for electrical power, control and counication cables Motor leads The data above data might be changed without prior notice. Spacial sizes are avaible on request Tablodaki bilgiler önceden haber verilmeden de ifltirilebilir. Talep edilmesi halinde özel ebatlarda imal edilebilir. UKAS A 06

8 TYPE LFMC - LIQUIDTIGHT FLEXIBLE STEEL CONDUIT / SIVI SIZDIRMAZ PVC KAPLI ÇEL K SP RAL BORU vinyl sheath galv.steel strip copper vinyl sheath galv.steel strip 1 1/ - inter locked 1/ - 1 1/ squard locked Arrowtite UL E22231 S v Geçirmez PVC Kapl çi Galvanizli Çelik Spiral Borular; s v s zd rmazl k özelli ine ihtiyaç duyulan tüm koflullarda kullan lan, Amerikan U.L onayl, NEC flartnamesine uygun elektrik tesisat borular d r. IP 67 kategorisindeki PVC Kapl Çelik Spiral Borular s v, ya ve di er kimyasallar n bulundu u motor ba lant lar klima kompresör ba lant lar ve benzeri dahili ve harici uygulamalarda güvenle kullan l r. Yüksek s ya dayan kl veya yanmaz PVC Kapl Çelik Spiral Borular ihtiyaç üzerine taraf m zdan temin edilmektedir. ÜRÜN ÖLÇÜ RULO MAKARA ORTALAMA BORU DIfi PVC KAPLI BORU Ç TAM BÜKÜLÜ A IRLIK/ KODU inches MetrikB R M B R M 100feet ÇAPI BORU DIfi ÇAPI ÇAPI D RSEK ÇAPI (feet) (feet) (pounds) (min / max) (min / max) (min / max) inches BK 3/ / / / BK 1/ / / / BK 1/ / / / BK 1/ / / / BK 3/ / / / BK 3/ / / / BK 3/ / / / BK / / / BK / / / BK 1 1/ / / / BK 1 1/ / / / BK 1 1/ / / / BK 1 1/ / / / BK / / / Description UL bonded strip 3/ - 1 1/ UL Liquidtight all sizes Sunlight resistant Flame retardant PVC jacket Hot dipped zinc galvanized low carbon steel core Available in black, grey, orange red an yellow Temperature Rating 0ºC to -30ºC Dry 60ºC Wet 70ºC Oil resistant 600 volt and lower circuits Direct burial in earth Concrete embedment Suitable for grounding per NEC 250.(7) Raised computer room floors per NEC 501 Hazardous location per NEC 645.5(D) Service entrance wiring up to 6 feet per NEC (15) Feeders and services for marina and boat yards References & Ratings UL 360, File Reference E26540, CSA Certified File LL5153, CSA C22.2 Number 56 NEC 250.(7), , 501.4(B)(2), 502.4(A)(1)(e), 503.3(A)(2), 5.7(A)(1), 645.5(D)(2), 60.21, 60.21, 60.42, 65.6(E),65.14(E) Canadian Electrical Code (CEC) Part I Clause UL approved for use in direct burial applications including concrete and earth burial (Sizes 3/ throught) Conduit in sizes 1 1/ and larger requires grouning conductor per NEC 250.(7) May be instlled under raised computer room floors per NEC 645.5(D) TYPE LFMC - VF LIQUIDTIGHT FLEXIBLE STEEL CONDUIT / SIVI SIZDIRMAZ PVC KAPLI ÇEL K SP RAL BORU vinyl sheath Arrowtite galv.steel strip S v Geçirmez PVC Kapl çi Galvanizli Çelik Spiral Borular; s v s zd rmazl k özelli ine ihtiyaç duyulan tüm koflullarda kullan lan elektrik tesisat borular d r. IP 67 kategorisindeki PVC Kapl Çelik Spiral Borular s v, ya ve di er kimyasallar n bulundu u motor ba lant lar klima kompresör ba lant lar ve benzeri dahili ve harici uygulamalarda güvenle kullan l r. Yüksek s ya dayan kl veya yanmaz PVC Kapl Çelik Spiral Borular ihtiyaç üzerine taraf m zdan temin edilmektedir. ÖLÇÜ inches 1/ 3/ 1 1/ 1 1/ 2 1/ RULO UZUNLU U (metre) lenght without coupling m max. BORU DIfi ÇAPI (min / max) BORU Ç ÇAPI (min / max) MIN. DÖNÜfi ÇAPI () / / / / / / / / / / / / / / / / / / The data above data might be changed without prior notice. Spacial sizes are avaible on request Tablodaki bilgiler önceden haber verilmeden de ifltirilebilir. Talep edilmesi halinde özel ebatlarda imal edilebilir. Description General wiring application Mechanical and moisture protection forconductors Sunlight resistant Flame retardant PVC jacket Hot dipped zinc galvanized low carbon steel core Very flexible 600 volt and lower circuits Industrial and machine tool applications Vibration and movement absorbing Temperature Rating 60ºC to -20ºC Dry 60ºC Wet 60ºC Oil resistant A 07

9 SCHEDULE 40 & 0 RIGID PVC CONDUIT AND SWEEPS National Pipe & Plastics Schedule 40 & 0 Heavy Wall PVC Conduit is manufactured in accordance with UL 651, ANSI/NEMA TC-2, and meets the requirements Federal Military Specification WC-104A and Article 352 of the National Electrical Code. Uses include aboveground, exposed, underground and concrete encasement applications. National Pipe and Plastics conduit is 0 wire rated and sunlight resistant. All sizes come in both 10 and 20 lengths with an integral bell on one end. Bu PVC boru tipi harici ortamlarda hem yer üstü ve yer alt nda hemde beton içine gömülü kullan m için NEC taraf ndan uygun bulunmufltur. Günefl fl ndan bir çok kimyasal maddeden ve korozif ortamlardan etkilenmez. Tamamen yal tkan olup, iletkenlerde güç kayb yada s nmaya neden olmaz. Yang na dayan kl olup mekanik korumada da yüksek direnç gösterirler. 0 C yal t ml iletkenlerin kullan m na uygundurlar. NOM. SIZE 1/ 3/ 1 1/ 1 1/ 2 1/ 3 1/ 5 6 METRIC DES. AVG. O.D. MIN. WALL SCH 40 SCH 0 Wt. Per 100 Feet SCH 40 SCH 0 Feet Per Bundle MIN. Socket Depth N/A 177 N/A U.L. Listed Sunlight resistant Rated for use with 0 C conductors CSA Listed, C22.2 No 2.2 ** * Rigid non-metallic conduit is normally supplied in standard 10 lengths with one belled end per length. For specific requirements, it may be produced in lengths shorter or longer than 10, with or without a bell. ** CSA Certification applies only to conduit manufactured in New York. ELBOWS National Pipe & Plastics Schedule 40 & 0 PVC Special Radius Conduit Sweeps are manufactured in accordance with UL 651 and NEMA TC2 Standards. These sweeps are subject to in-process monitoring and quality control inspection to assure conformance with design specifications. Belled-End sweeps and optional bend radius are available upon request. Standard radius NOM. A MIN. WALL SIZE O.D. AVG. SCH 40 SCH 0 B R AVG. STD. RADIUS PACKAGE QTY / / / / / / N/A Special radius - 0 NOM. SIZE A O.D. AVG. B AVG. Radius & Package Quantity Qty 2 Qty 30 Qty 36 Qty Qty X 100 X 100 X 200 X 200 X / X 100 X 100 X 200 X 200 X / X 100 X 100 X 200 X 200 X X 75 X 50 X 100 X 100 X / X 50 X 50 X 100 X 100 X X 50 X 50 X 50 X 50 X / X 50 X 50 X 50 X 50 X X 50 X 50 X 50 X 50 X X 25 X 25 X X 25 X , 30, 45 special radius sweeps avaible A 0

10 TECHNICAL GUIDELINE Table 1: Premises Cable Conduit Fill Guidelines Trade Size Conduit Area of Conduit Minimum Radius of Bends Internal Diameter Crosss sectional Area Maximum Occupancy Recoended A B C D E 1 Cable 53% Fill 2 Cables 31% Fill 3 Cables or more, 40% Fill Layers of Steel Within Sheath Other Sheath in 2 in2 2 in2 2 in2 2 in2 in in 1/ / / / / / , , The first step in sizing a conduit is to determine the number of cables to be placed in the conduit. This will determine the maximum fill allowance (see Table 2 below). Table 2: Maximum Fill Ratio Number of Cables in Conduit Maximum Fill (%) 1 53% 2 31% 3 or more 40% This document should be used as a guideline for cable fill requirements. Please keep in mind that these requirements are min/max values and do not take into account additional factors that may affect conduit fill or future cabling requirements. One of the more important of these factors is maximum cable pulling tension, which may limit conduit fill more so than these guidelines and should be carefully examined. A 0