PLUMBING
AFE 32 AVE 100 FloPlast Air Admittance Valve Functioning Diaphram Seal Carrier FLOPLAST AIR ADMITTANCE VALVES The valves have been designed for above-ground use in conjunction with Building Regulations, (PART H1) and systems designed in accordance with this document. FloPlast s Air Admittance Valves carry the British Standards Institution (BSI) Kitemark (KM512474), as having met the performance requirements of BS EN 12380: 2002 and have been designated with an rating. Diaphram Seal BS EN 681 Valve Body FloPlast s Air Admittance Valves provide a means o f ventilation to the drainage system to prevent the loss of water seals in traps and consequent release of foul air into the building. The drainage system, installation and use of FloPlast s Air Admittance Valves must be in accordance with the design data and installation sections of this document. Positive Pressure in Closed Position Delivery and Site Handling Negative Pressure in Open Position Kirlenme Valves, complete ya da hasar with alma their risklerini adaptors sınırlamak (when amacıyla, applicable), Hava along Alma Şapkaları with installation ve beraberlerinde instructions gelen are adaptörler, supplied montaj in talimatlarıyla cardboard birlikte boxes karton and polyethylene kutular ve polietilen bags, to torbalar limit the içerisinde risk of contamination teslim edilmektedir. or damage. Tüm hava All alma valves şapkalarının, must be kullanı- stored lıncaya upright kadar, in their kutularında boxes ve until dik required konumda for depolanmaları use. önerilir. FloPlast s AFE 32 Air Admittance Valve, comprises of an FloPlast s AVE100 Air Admittance Valve, comprises an injection-moulded, two-part acrylonite butadine styrene injection-moulded, two-part poly vinyl-chloride (PVC-U) (ABS) body, snapped together incorporating an ethylene body, screwed together incorporating an EPDM sealing propylene diene monomer (EPDM) sealing ring. The ring. The valve incorporates a sliding ABS injection valve incorporates a sliding ABS injection moulded disc moulded disc and EPDM seal (poppet) which acts as the and EPDM seal (poppet) which acts as the opening and opening and closing seal. closing seal. The AVE100 valve has been designed for use with With the use of the universal adaptor (provided with the European designated 100mm pipe. product), the can also to be installed onto 40mm and 50mm UK designated pipe. Hava The Alma valves Şapkaları incorporate atık su boruları spigots için with belirlenen, diameters BS EN that 1329-1: are in 2000, accordance BS EN 1455-1: with 2000, the standards BS5255: 1989 for ve waste BS 4514: pipe, 2001 including: dahil tüm BS standartlara EN 1329-1: uygun 2000, çapta BS tapalara EN 1455-1: sahiptirler. 2000, BS5255: 1989 and BS 4514: 2001. Continuous quality control is exercised during their manufacture and assembly, including visual checks, checks on Hava Alma Şapkalarının üretimi ve montajı süresince, her bir ürün için sürekli olarak, gözle kontrol, ebat doğruluğu ölçümleri ve yüzde yüz işlevsellik dimensional testi gibi accuracy kalite kontrol and testleri 100% uygulanmaktadır. functional testing Hammaddeler of each ve product. dışarıdan The satın raw alınan materials malzemeler, and BSI bought-in tarafından goods denetlenen, are ISO 9001 subject Kalite to Yönetim quality Sistemi controls (FM 501414) as defined uyarınca within açıklanan our ISO9001 kalite kontrollerine Quality tabidirler. Management System (FM 501414) audited by BSI Tablo 1 Valve Size Product Code BS EN 12380 Designation Distribütöre The legend ait of açıklayıcı the distributor bilgiler, paket is incorporated üzerinde gösterilmektedir. on to the lid Ek of olarak, the product tüm FloPlast and is Hava shown Alma on Şapkaları, the packaging. detayları kutu In üzerinde addition, gösterilen all FloPlast BS EN valves 12380: 2002 have standartları CE mark designation uyarınca sınıfı CE to işaretine BS EN sahiptirler 12380: 2002, the details of which appear on the boxes Design Data The FloPlast FloPlast Hava Alma Air Admittance Şapkaları, BS Valves 12056-1: when 2000 used ve BS in 12056-2: above-ground 2000 standartları drainage uyarınca systems tasarlanmış designed yer üstü with drenaj BS 12056-1: sistemleriyle 2000 and BS birlikte 12056-2: kullanıldıklarında, 2000 will: aşağıda belirtilen faydaları sağlayacaklardır: Boşaltma borularında basıncın düştüğü koşullarda hava alımını sağlamak ve sifonlardaki su kaybını önlemek Admit air under conditions of reduced pressure in the discharge pipes and prevent water seals in traps from being drawn or evacuated. Drenaj sisteminden kötü kokuların binaya sızmasını önlemek Prevent the release of foul air from the drainage system. Hava Alma Contribute Şapkasını to da the içeren ventilation drenaj borusunun of the main bağlandığı drain to ana which havalık the hattının discharge havalandırılmasına stack incorporating katkıda bulunmak the valve is connected. The 32 32mm ve 40mm and 40mm Hava Alma valves Şapkaları, are designed küçük çaplı for atık connection su branşmanlarındaki to waste pipes sifonlama to prevent sebebiyle water oluşan, loss sifonlardaki from trap seals su kaybını by self and induced önlemek siphonage üzere tasarlanmıştır. arising from water flow in small diameter branch discharge pipes. The 50mm 50mm Hava valve Alma Şapkası is for use branşman on branch atık borularında discharge kullanılmak pipes. üzere tasarlanmıştır. The 100mm FloPlast 100mm Hava Alma valves Şapkaları, are designed birbirleriyle 45 metre for ya birlikte use da 10 on kat ya discharge da yüksekliğindeki ayrı ayrı kullanılabilecek stacks tahliye up to bacalarında 45 şekilde metres tasarlanmışlardır. kullanılmak or 10 storeys üzere tasarlanmışlardır. high. The FloPlast valves are designed for use in association with each other or separately. European designated size 32mm 40mm 50mm 100mm AVE100 = permitted to be used below flood level in locations where the temperature is in the range of -20 C to +60 c
age System Design BS age EN 12056-1: systems 2000 ve BS designed EN 12056-2: in 2000 accordance ile uyumlu with olarak BS tasarlanmış EN 12056-1: drenaj sistemleri, 2000 and Tablo BS 2 de EN gösterilen 12056-2: hava 2000 akış should be verileri based temel on alınarak the airflow tasarlanmıştır. data given in Table 2. Table 2 Nominal size of pie 32mm 6.5 100mm 43.0 Airflow (L/S) Note: These results are based on tests carried out by the United Kingdom Building Research Establishment (BRE) in accordance with BS EN 12380: 2002 To Kendiliğinden prevent self-siphonage sifonlamayı önlemek a connection için, kapanın to the 1500mm AFE 32 içerisinde valve is bir required hava within alma 1500mm şapkası kullanılması of the trap. gereklidir. Bir sıra lavaboda, vakumdan kaynaklanan sifonlamayı önlemek için, havalık kolonundan en uzaktaki iki lavabo arasına bir To prevent induced siphonage in a row of wash-basins, a AFE 32 valve can be fitted between the two washbasins furthest Hava Alma Şapkası monte edilebilir. away from the discharge stack. Hava alma şapkası, septik tanklar ya da foseptik çukurları için tek havalandırma yöntemi olarak kullanılmamalıdır. Air admittance valves should not be used as the only ventilation to septic tanks or cesspools. Hava alma şapkası, bina içerisinde, kolayca erişilebilecek ancak kurcalanmaya maruz kalmayacak bir konumda monte edilmelidir. The valve should be installed within the building where it is easily accessible but not subject to interference from vandals. Effects on Water Seals Hava alma şapkaları düşük basınca maruz kaldıklarında sistem içerisine makul miktarda hava alacaklar ve böylece su bariyer- The valves will admit sufficient quantities of air into the stack when they are subjected to a reduced pressure and there by lerinin tesisat sifonları içinde kaybolmasını önleyeceklerdir. prevent loss of the water seals in appliance traps. Drenaj sistemi içerisindeki basıncın arttığı şartlar altında, her bir hava alma şapkası kapalı kalacak ve böylece kötü kokuların Under bina içerisine conditions sızmasını of increased önleyecektir. pressure in the drainage system, each valve will remain closed, thereby preventing the release of foul air into the building. Su sızdırmazlık sistemi içerisindeki seviyeyi arttırmaya yetecek bir basınç artışı durumunda ya da kötü kokuların sifon içerisin- A de pressure köpürüp kabarması increase sufficient halinde bu to durum, raise the drenaj level kanalında in the water bir tıkanıklık seal or olduğuna, to cause sistemin foul air to aşırı bubble yüklendiğine up through veya the yanlış seal is an indication kullanıldığına that işaret either eder. a drain blockage has occured, the system is being overloaded or otherwise misused. Maintance FloPlast Hava valves Alma do Şapkaları not normally şartlarda require bakım maintenance. gerektirmez. Kaza sonucu hasarlanan ya da kurcalanma neticesinde zarar In gören the FloPlast event Hava of accidental Alma Şapkaları, damage yenileriyle or vandalism değiştirilmelidir. the FloPlast valves must be renewed. Durability Installation Installation Montaj bu talimatlara must be uygun carried biçimde out in gerçekleştirilmelidir. accordance with these instructions. FloPlast AVE100 AVE100 ürünleri are available sırasıyla, Birleşik in both Krallıkta UK and ve European Avrupa da belirlenen designated ebatlarda, sizes BS4514: respectively, 2001 ve supplied BS EN 1329-1: with 2000 solvent standartlarıcement na uygun sockets PVC-U borulara enabling yapıştırmalı a solvent bağlantıyı cement mümkün connection kılan to soketleriyle PVC-U pipes birlikte to sunulmaktadır. BS4514: 2001 and BS EN 1329-1: 2000. FloPlast AFE 32 Hava Alma Şapkaları, Birleşik Krallıkta ve Avrupa da belirlenen ebatlarda, ana gövde üzerinde BS EN 1329-1: 2000, BS EN FloPlast AFE 32 valves are available in both UK and European designated sizes, supplied with a solvent weld 1455-1: 2000, BS5255: 1989 standartlarına uygun, adaptörle 32mm PVC-U ve ABS borulara yapıştırmalı bağlantıyı mümkün kılan socket soketleriyle on the birlikte main sunulmaktadır. body for 32mm Soketler with yapıştrılmadan an adaptor kullanılmamalıdır. enabling the product to be connected to solvent welded PVC-U and ABS pipe to BS EN 1329-1: 2000, BS EN 1455-1: 2000, BS5255: 1989 FloPlast AVE100 Hava Alma Şapkaları, en yüksek branşman boru bağlantısının en az 200mm üzerinde bir noktaya dikey olarak monte FloPlast edilmelidir). AVE100 FloPlast hava valves alma must şapkaları, be fitted BS EN in a 12380-1: vertical 2002 position uyarınca a minimum derecelendirmesine of 200 mm above sahip olduklarından, the highest havalandırılan branch connection rezervuarlardan. As altına FloPlast da konumlandırılmaya valves are uygundur. designated to BS EN 12380-1: 2002 it is possible to locate them below the lowest reservoir being vented. FloPlast Hava Alma Şapkaları, havalandırılmakta olan borunun en az 100mm üzerinde bir noktaya dikey olarak monte edilmeli- FloPlast dir. AFE Hava 32 Alma valves Şapkaları, must be BS fitted EN 12380-1: in a vertical 2002 uyarınca position a derecelendirmesine minimum of 100mm sahip above olduklarından, the pipe havalandırılan being vented. rezervuar- As FloPlast lardan en valves altta yer are alanı altına designated konumlandırılmaya to BS EN da 12380-1: uygundur. 2002 it is possible to locate them below the lowest reservoir being vented. Hava Alma Şapkaları atık ve/veya havallık borularına kolaylıkla monte edildiklerinden, çatı kaplamasını delme zorunluluğunu ortadan The kaldırırlar. valves Sistemin are easily uygun installed çalışmasını in discharge sağlamak üzere, and/or sızdırmazlık ventilation sağlayan pipes yüzeylerin and eliminate herhangi the bir need şekilde to penetrate kirlenmemesine the roof özen covering. gösterilmelidir. Care should be taken to avoid contamination of the sealing surfaces, as this may affect airtightness Floplast Air Admittance Valve Functioning FloPlast AFE 32 32mm 40mm Up to 5 washbasins FloPlast AFE 32 Valve 50mm minimum FloPlast Hava Alma Şapkaları, drenaj sistemlerinde geleneksel olarak kullanılan malzemelerden imal edilmiştir. Sürekli olarak FloPlast valves are manufactured from materials conventional in drainage systems. Repeated opening and açılıp kapanma, sızdırmazlık sisteminin ya da hava alma şapkasının düzgün çalışmasını olumsuz yönde etkilemeyecektir. Bu closing will not adversely affect the sealing or operation of the valve. When used in the context of this data broşürde belirtilen kapsam dahilinde kullanıldığı sürece, ürünün kullanım ömründe önemli değişiklik olmayacak ve üzerine sheet the product will not be subject to significant deterioration and will have a life equivalent to that of the monte edildiği drenaj sisteminin ömrüne eşdeğerde bir kullanım ömrüne sahip olacaktır. drainage system in which it is installed.
x 2 Bas in AV110/ AF110 14th 12th 12th 11th W C Ba th W C Ba th Sh ower W C Ba th W C Ba th AV110/ AF110 7th 6th 5th 4th 3rd 2nd 1 1st 1 Sewer 1st 1 Basement 1st 1 1 Basement 2nd 1 1 Basement 3rd 1 Sewage Tank Pump
ALTAY MEKANİK ISI SİSTEMLERİ İNŞ. TUR. İÇ ve DIŞ. TİC. LTD. ŞTİ. tescilli markasıdır. Anadolu Bulvarı 2. Cadde A.T. B. İş Merkezi E Blok No: 92 06105 Macunköy-Ankara/TÜRKİYE Tel: +90(312) 397 30 60 (pbx) Fax: +90(312) 397 33 44 info@altayisisistem.com.tr www.altayplumbing.com.tr