LASER SHOW SYSTEM SINGLE LASER SERIES Türkiye Yetkili Temsilcisi & Ithalatcı Firma: MODEL SL- KARA ELEKTRONIK.LTD.STI. SL- KONYA - TÜRKİYE w w w. k a r a e l e k t r o n i k. c o m. t r KULLANICI KILAVUZU SHINP OPTOELECTRONICS SCI-TECH USER GUIDE MADE IN CHINA
Yukarıdaki çözümleri deneyip yinede yanıt alamazsanız satıcınızla veya teknik destek ile iletişime geçiniz. Ürünün patent ve tüm hakları, SHINP Optoelectronics Sci-Tech Co., ile ortak Kara Elektronik Ltd, ait olup içerisindeki lazer donanımları ve yazılımları da dahildir. Izin verilmeden kısmen veya tamamen kopyalanamaz, coğaltılamaz. Page 5
. Standard XLR mikrofon kablosu ile üniteleri birbirlerine XLR konnektor ile ürünün arka Genel Bilgiler tarafından bağlayın.. Bütün üniteleri çalıştırın. Slave olarak bağlanan üniteler ana unite ile aynı anda faal Paket Açılımı: olacaktır. Ürünümüzü tercih ettiğiniz için teşekkür ederiz. Lütfen bu kullanıcı kılavuzunu ürünü 5. Kendi bünyesindeki dahili mikrofon vasıtası ile sese duyarlıdır. Ses hassasiyetini ana ünitenin kullanmaya başlamadan once dikkatlice okuyunuz. Gelecekte de gerekebilecek olacağından arkasındaki hassaslık ayar bölümünden ayarlayabilirsiniz. Ürün panelinde Sound Active modu muhafaza ediniz. Ürünümüz mükemmel lazer programlari ve efektleri yaratır. Bir dizi ciddi için LED uyarı ışığı bulunmaktadır. testten geçtikten sonra satışa sunulur. Lütfen paket içeriğini kontrol ediniz. Eğer hasarlı, bağlantı noktaları açılıp kapanmış bir ürünle karşılaşırsanız satıcınızla iletişime geçin. :Slave N:Slave Notlar:. DMX konsol Master-Slave operasyonda kullanılamaz (Sound Active or AUTO mode ).. Sadece bir Master bulunabilir. Digerleri Slave olarak tanıtılır. Uyarı: Olası Durumlar Paket içeriği:. Laser Işık: Adet. Güç kablosu: Adet. Kullanıcı Kılavuzları: Adet. Lazer ışınlarını asla canlı gözüne doğru tutmayın.. Ard arda ürünü açıp kapatmayın.. Topraklı elektrik hattı kullanın.. Kendi başına çalışırken, güç ışığı açık, Sound Active ışığı açık görünmüyor ve Lazer ışığı. Ürün kapalı alan kullanımı için üretilmiştir. Su, toz, nem gibi unsurlardan uzak tutunuz. çalışmıyorsa ürünü kontrol edin. Master modda çalıştığından emin olun. Sarsıntısız bir yerde kullanınız. Çalışma sıcaklığı 8~0 derece olup aralıksız. Master-Slave operasyonunda, slave unitesi çalışmıyorsa; saatten fazla kullanmanız ürününüzün ömrünü azaltabilir. A. Master'a sadece tek cihazın bağlı oldugunu, digerlerinin Slave moduna ayarlı 5. Belirli aralıklarla ürününüzü kuru bir bez ile lens ve diger bölümlerini temizleyebilirsiniz. olduğundan emin olun. Lens ömrünü uzatmak için cizilmemesini sağlayınız. B. Ürünün DMX consol modunda çalışmadığından emin olun. 6. Garanti ve son kontrol bandrollerini çıkarmayınız. Aksi takdirde garanti kapsamı dışıdır. C. Kabloların ve bağlantıların iyi olduğundan emin olun. 7. Daima aynı tip priz ve elektrik akımı ile kullanınız. Farklı voltajlar ve akımlar ürünün şok. DMX modda çalışması gerekirken, laser kapalı ve DMX ışığı yanmıyorsa almasına, yanmasına veya başka hasarlar görmesine sebeb olabilir. DMX için ayarlı olduğundan emin olunuz, bağlantıları kontrol ediniz.. DMX operasyon sırasında, DMX tarafından kontrol sağlanamıyorsa ancak DMX ışığı DANGER yanıyorsa, DMX konsol ve ürün aynı kanala bağlı olduğundan emin olunuz. LASER RADIATION AVOID EXPOSURE 5. Eğer ünite hata verirse ürünü kapayıp 5 dakika bekleyip geri açınız. TO BEAM CLASS B LASER PRODUCT! Page Page
Teknik Özellikler Arka Panel. Voltaj: AC0V/ 0V, 50HZ/60HZ, Fiş Tipi: A/50V. Uygulanabilir Güç: 0W. Laser: SL-: Yeşil Laser,0~0mW@5nm SL-: Kırmızı Laser,00mW@650nm. Çalışma Modları: Sound Active, Master-Slave 5 5. Grafikler & Efektler: 50den fazla şekil, 00den fazla efekt. 6. Arayüz: pins XLR jack Maser-Slave bağlantısı için. Arka Panel Şekli 6. Boyut: L*W*H=0*0*0mm. Güç Jack. Sogutma Fanı 7. Ağırlık:.5Kg. Audio Hassaslık Ayarı. Master / Slave Geçişi 5. Bağlantı Ayarları Özellikler Çalışma. DPSS Laser Kendi başına çalışma (Sound Active, AUTO mode) Diode-Pumped Solid State yeşil laser kullanılır, uzun ömürlü, stabildir ve optimizedir. Bu mod ürünü kendi başına veya sese duyarlı olarak çalışmasını mümkün kılar.. Çeşitli programlama seçenekleri vardır.. Ürünü gerekn pozisyonda sabitleyin. (yatay veya düzey). Kırmızı ve yeşil ışınlarla, 50den fazla laser şekil, 00den fazla laser efekt.. Sound Active veya AUTO moda göre dipsivçleri ayarlayın.. LED uyarısı ve kapanma. Ürünü çalıştırın. Sound Active modda ürününüzü kullanırken müzik bittikten 8 saniye sonra ürün. Kendi bünyesindeki dahili mikrofon ile sese duyarlıdır. Ses hassasiyetini ana ünitenin kendiliğinden kapanir. arkasındaki hassaslık ayar bölümünden ayarlayabilirsiniz. Ürün panelinde Sound Active modu için LED uyarı ışığı bulunmaktadır. Ön Panel :Master N:Master Master-Slave Operation Bu mod sizin bir çok ürünü aynı anda kullanabilmenize olanak tanır. Ön panel Şekli. Ürünleri gerekn pozisyonlarda sabitleyin. (yatay veya düzey).. Laser aparatı. Sound active mikrofonu. Bir ürünü ana ünite (Master) olarak belirleyin, diğerlerinide Sound Active veya AUTO. Sound active ışığı:mavi. Güç gösterge ışığı:kırmızı moda yan ürünler olarak ayarlayın. Diğer üniteler mutlaka Slave moda ayarlı olmalıdır. Page Page
After trying the above solution you still have a problem, please contact your dealer or our company for service. The copy right of this product is belongs to SHINP Optoelectronics Sci-Tech Co., Ltd, including laser hardware and software. Do not mock, copy or extract without permission of SHINP. Page 5
. Use standard XLR microphone cable chain your units together via the XLR connector General instructions on the rear of the units. For longer cable runs we suggest a terminator at the last fixture.. Turn on the all units' power, the units begins reset, then the unit begins working. The Unpacking: slave units will react the same as the master unit. Thank you for purchasing this product. Please read user guide for safety and operations inf- 5. The units will react to the low frequencies of music via the internal microphone. Adjust ormation before using the product. Keep this manual for future reference. This product can the audio sensitivity knob on the back of the master unit to make the unit more or less se- create perfect laser programs and effects since it has passed a series of strictly tests before nsitive in sound active.the panel has LED indicating for sound active. Note: delivery. Please check the attachments listed on the page after opening the carton. In the event of carton damage or attachment missing in transit, please contact your dealer or our after sales service department. Attachments:. DMX console controlling can not be use in Stand-Alone and Master-Slave Operation. Notice:. Laser Light: PCS. Power Cable: PCS. User Guide: PCS. There should be only one master unit in Master-Slave Operation.. Do not exposure the human eye direct to laser beam. Troubleshooting. Do not turn on and off the unit frequently.. Before using this unit make sure the power supply is ground.. This unit is intended for indoor use only and should be prevented form water, moisture. If the power supply indicator doesn't light up and the laser doesn't work, please check the and shake. The working temperature of this unit is 8~0, do not use this continuously power supply and the input voltage. :Slave over hours, otherwise it shortens the lifetime of the unit.. In Stand-Alone operation, if the power supply indicator is light up and sound active indi- 5. Use cleaning tissue to remove the dust absorbed on the external lenses periodically to op- cator isn't light up, but the laser is shut off doesn't work. timize light output. A. Because sound is too small make for laser shut off in sound active, please increase the 6. Do not remove or break the warranty label, otherwise it void the warranty. music volume or increase audio sensitivity with sensitivity knob, please check as below. 7. Always replace with the exact same type fuse, replacement with anything other than the B. Please check if unit has been set up in slave mode, then set up in master mode. specified fuse can cause fire or electric shock and damage your unit, and will void your ma-. If the units are in Master-Slave operation, slave unit don't function, please check as below. nufactures warranty. A. Make sure to there's only one master in the chain, and the others are set in slave mode. B. Make sure to control the unit without DMX console controlling. DANGER C. Make sure to take a good quality power cable and connection. LASER RADIATION AVOID EXPOSURE. If the output beam direction above isn't the right way, please restart the unit. TO BEAM CLASS B LASER PRODUCT 5. If the unit is fail, please turn off the unit, then turn on again after 5 minutes. N:Slave! Page Page
Technical Specification Rear Panel. Voltage: AC0V/ 0V, 50HZ/60HZ, Fuse: A/50V. Rated Power: 0W. Laser: SL-: Green Laser,0~0mW@5nm SL-: Red Laser,00mW@650nm. Working Modes: Sound Active, Master-Slave 5 5. Graphics & Effects: more than 50 patterns, over 00 effects 6. Interface: pins XLR jack for Maser-Slave linking Rear Panel Figure 6. Size: L*W*H=0*0*0mm. Power Jack. Cooling Fan. Audio Sensitivity Knob 7. Weight:.5Kg. Master-Slave Switch 5. Linking Jack Features Operation. DPSS Laser Stand-Alone Operation. Use Diode-Pumped Solid State green laser, stable output and long working life. The operation allows a single unit to react to the beat of the music in the master mode.. Various programs. Install the system in a suitable position (laying or appending). The laser beams are controlled by sound active, more than 50 laser patterns, over 00. Turn Master-Slave switch to the master position on the unit. laser effects. The unit has linking function, lots of units will synchronization job.. Turn on the unit power, the unit begins reset, then the unit begins working.. LED Indicating and shut-off in sound active. The unit will react to the low frequencies of music via the internal microphone. Adjust The panel has LED indicating for sound active. The unit will shut off after 8 seconds the audio sensitivity knob on the back of the unit to make the unit more or less sensitive in when the music stops. sound active.the panel has LED indicating for sound active. Front Panel :Master N:Master Master-Slave Operation This operation will allow you to link up to units together without console. Front Panel Figure. Install the system in a suitable position (laying or appending).. Laser Aperture. Sound Active Microphone. Choose a unit to function as Master mode, turn Master-Slave switch to the master po-. Sound Active Indicator:Blue. Power Indicator:Red sition on the unit. The others must be set to Slave mode, Turn Master-Slave switch to the slave position on the unit. Page Page