İçerik Mevcut PLC Modelleri Mevcut PC Bölüm 1 - Kurulum- Başlatma 1. Kurulum 1-1. CX-Programmer'ın kurulumu 1-1 1-2. CX-Server'ın kurulumu 1-4 2. CX-Programmer'i başlatma 1-6 3. Yeni Proje Yaratmak ve Cihaz Tipleri 1-7 4. Ana Pencere 1-8 4-1. Uygun SYSWIN Tuş Alokasyonu 1-9 4-2. Bölüm 1-10 4-3. Gereksiz Pencerelerin Ekrandan Silinmesi 1-12 5. Program Yaratma 1-13 5-1. Normalde Açık Kontağın Girilmesi 1-14 5-2. Bobinin Girilmesi 1-15 5-3. Sembol Komutunun Girilmesi 1-17 5-4. Network Komutunun Girilmesi 1-18 5-5. Normalde Kapalı Kontağın Girilmesi 1-18 5-6. Ek Komutların Girilmesi 1-19 5-7. Yükselen Kenar Kontağın Girilmesi 1-20 5-8. Düşen Kenar Kontağın Girilmesi 1-20 5-9. Yukarı Çizgi Çizilmesi 1-21 5-10. Aşağı Çizgi Çizilmesi 1-21 5-11. İleri Seviyeli Fonksiyonlar 1- Komut İsmi Girilmesi 1-22 5-12. İleri Seviyeli Fonksiyonlar 1- Faydalı Fonksiyonlar 1-23 5-13. Yardımcı Rölenin Girilmesi -1.0 İkinci Clock Puls Bit'i 1-24 5-14. İleri Seviyeli Fonksiyonlar 2- Farklı Fonksiyonların 1-25 Girilmesi 5-15. OR Basamaklarının Girilmesi 1-26 5-16. İleri Seviyeli Fonksiyonlar 3 - Fonk No. ile Giriş 1-27 5-17. Timer Fonksiyonunun Girilmesi 1-28 5-18. Sayıcı Fonksiyonunun Girilmesi 1-29 5-19. Basamakların Düzeltilmesi 1..Kopyala & Yapıştır 1-30 5-20. Basamakların Düzeltilmesi 2...Kombine, Ayrı 1-31 5-21. END Komutunun Girilmesi 1-31 Bölüm 2 Online Çalışma 1. Program Hata Kontrolü (Derlemek) 2-1 2. "Online" Olma 2-2 3. İzleme 2-3 4. İzleme -2 Program İçindeki Birçok Bölgenin Birkez İzlenmesi 2-4 5. İzleme -3 Hex Olarak İzleme 6. İzleme -4 Pencereyi İzleme 2-4 2-5 7. İzleme -5 Mevcut Değerin Değişmesi ve Binary Olarak İzlenmesi 2-6 8. İzleme Penceresinin Fonksiyonları 9. İzleme -6 İzleme Penceresi -2 2-7 2-8 10. İzleme -7 Uzun Basamakların Kıvrılarak Görüntülenmesi 2-9 11. İzleme -8 Farklılıkların İzlenmesi 2-10 12. Zorlamalı Set On/Off 2-11 13. Zorlanmış Setlerin- on/off bit'lerin Listesinin Görüntülenmesi 2-11 14. Timer'ın Set Değerinin Değiştirilmesi 2-12 15. Timer'ın Mevcut Değerinin Değiştirilmesi 2-12 16. Fonksiyon Bulma -1 Adres Referans Seçeneğinden Bulma 2-13 17. Fonksiyon Bulma -2 Basamak Bulmayı Tekrarlamak 2-14 18. Fonksiyon Bulma -3 Komut İçindeki Anahtar Sözcükle Bulma 2-16 19. Fonksiyon Bulma -4 Basamak Komutuna Gitmek 2-17 20. Fonksiyon Bulma -5 Bit Adreslerini Bulma 2-18 21. Online Düzeltme 2-19
Mevcut PLC Modelleri CX-Programmer, ekteki tabloda belirtilen PLC modellerini desteklemektedir. Seri CPU Ünitesi Modeli CS1 CS1-H CJ1 CJ1-H C1000H C2000H C200H C200HX C200HG C200HE C200HX-Z C200HG-Z C200HE-Z C200HS CPM2* CPM2*-S* CPM1/CPM1A CQM1H CQM1 CV1000 (*1) CV2000 (*1) CV500 (*1) CVM1 CVM1-V2 IDSC SRM1 CS1H-CPU67/66/65/64/63 (-V1) CS1G-CPU45/44/43/42 (-V1) CS1G-CPU45H/44H/43H/42H CS1H-CPU67H/66H/65H/64H/63H CS1D-CPU67H/65H CJ1G-CPU45/44 CJ1M-CPU12/13/22/23 CJ1G- CPU45H/44H/43H/42H CJ1H-CPU66H/65H C1000H-CPU01 C2000H-CPU01 (Sadece Simplex sistemde) C200H-CPU01/02/03/11/21/22/23/31 C200HX-CPU34/44/54/64 C200HG-CPU33/43/53/63 C200HE-CPU11/32/42 C200HX-CPU34-Z/CPU44-Z/CPU54-Z/CPU64-Z/CPU65-Z/CPU85-Z C200HG-CPU33-Z/CPU43-Z/CPU53-Z/CPU63-Z C200HE-CPU11-Z/CPU32-Z/CPU42-Z C200HS-CPU01/03/21/23/31/33 CPM2A-20CD/30CD/40CD/60CD CPM2C-10CD/10C1D/20CD/20C1D CPM2C-S100C/110C CPM2C-S110C-DRT CPM1(A)-10CDR/20CDR/30CDR/40CDR (-V1) CQM1H-CPU11/21/51/61 CQM1-CPU11/21/41/42/43/44/45 CV1000-CPU01 (-V1) CV2000-CPU01 (-V1) CV500-CPU01 (-V1) CVM1-CPU01/11 (-V1) CVM1-CPU01-V2/CPU11-V2/CPU21-V2 IDSC-C1DR-A/C1DT-A SRM1-C01/C02 (-V2) C200PC-ISA01 (C200HG-CPU43 *2) C200PC-ISA02-DRM (C200HG-CPU43 *2) C200PC-ISA02-SRM (C200HG-CPU43 *2) C200PC-ISA12-DRM (C200HX-CPU64 *2) C200PC-ISA12-SRM (C200HX-CPU64 *2) CS1PC-PCI01-DRM (CS1G-CPU45 *3) *1: CX-Programmer, SFC'yi desteklemez. *2: SYSMAC Board ile bağlanmak için parantez içindeki PLC tiplerini belirtiniz. Sadece bu PLC'leri seçtiğinizde SYSMAC Board'u network tipi olarak seçebilirsiniz. *3: SYSMAC CS1 Board ile bağlanmak için parantez içindeki PLC tiplerini belirtiniz. Sadece bu PLC tiplerini seçtiğinizde SYSMAC CS1 Board'u network tipi olarak seçebilirsiniz.
Mevcut PC Donanım Gereksinimleri Malz. OS Windows95/98/NT4.0 Service Pack6 Windows2000/Me Windows XP PC PC/AT Uyumlu PC/AT Uyumlu PC/AT Uyumlu CPU Pentium CPU 133MHz ya da büyük Memory (RAM) 48M byte ya da büyük (64M byte ya da büyük) Pentium CPU 150MHz ya da büyük 96M byte ya da büyük (128M byte ya da büyük) Pentium CPU 300MHz ya da büyük 128M byte ya da büyük (192M byte ya da büyük) Hard disk space 100M byte ya da fazla 100M byte ya da fazla 100M byte ya da fazla Display CD-ROM drive En az bir tane En az bir tane En az bir tane Haberleşme Portu En az bir tane RS-232C Port Item OS Windows95/98/NT4.0 Service Pack6 Windows2000/Me Windows XP PC PC/AT Uyumlu PC/AT Uyumlu PC/AT Uyumlu CPU Pentium CPU 450MHz ya da büyük Memory (RAM) Hard disk space Display Pentium CPU 450MHz ya da büyük Pentium CPU 600MHz ya da büyük CD-ROM drive En az bir tane En az bir tane En az bir tane Haberleşme Portu En az bir RS-232C Port
Installation to Startup
Installation to Startup Program check After checking the contents, click [Yes] if you accept all the terms.
Installation to Startup Opening a new project
Installation to Startup Program check The [Choose Destination Location] dialog is displayed. Click [Next].
Installation to Startup Opening a new p roject Device type settings Before starting to use CX-Programmer, be sure to read Readme file.
Installation to Startup
Installation to Startup
Alt 1 Alt 2
Installation to Startup C 0 Switch 1
Installation to Startup O 100 Coil 0 R Useful Function: Automatic check of duplicated coils If a duplicated coil is entered during program creation, the following message is displayed and you can notice that the coil is duplicated right away.
Installation to Startup Opening a new project Alt Y
Installation to Startup Copy&Paste of symbol comments is possible between Excel and CX-Programmer too.
Installation to Startup Program check / 1 Sensor 1
Installation to Startup O 101 Coil 1 R Alt
Installation to Startup Program check C 100 C 101
Installation to Startup Opening a new project Ctrl U O 200 Bobin 2 R C 200 O 300 Bobin 3 Ctrl V
Installation to Startup Opening a new project I ++ d0 R
Installation to Startup
Installation to Startup C
Installation to Startup Opening a new project I @MOV #0 D100 Attach @ (at mark) before instructions. It makes the instructions differential. R
Installation to Startup W 3 W 4 Refer to the section 5-6 to enter annotations.
Installation to Startup Show the [New Instruction] dialog. I 021 The instruction corresponding to the entered Fun No. is displayed. #0 D0 R Note: The Fun No. of MOV depends on PLC types. CS-series -> 021 CJ-series -> 021 CV-series -> 030 C-series -> 21
Installation to Startup Refer to the former pages to enter rungs and comments. / T0 Timer 1 I TIM 0 #30 R
Installation to Startup Opening a new project Refer to the former pages to execute coding. I CNT 0 #5 R C O C0 402 R
Installation to Startup Move the cursor to this position. The rung is inverted as shown right. Ctrl C Press the key to move the cursor to this position. Ctrl V Click each instruction and then change the bit numbers.
Installation to Startup Drag the mouse with the left mouse button pressed to invert rungs that you want to combine. Combine of rungs Click the right mouse button and select [Combine] from the popup menu. Split of rungs Drag the mouse with the left mouse button pressed to invert a part of the rung that you want to split. Click the right mouse button and select [Split Rung] from the popup menu. At the creation of a new project, a section of the END instruction only is automatically generated. You do not need to enter an END instruction.
Online to Transfer Errors and addresses are displayed on Output Window. Double-click a displayed error, and the cursor in Ladder Diagram will go to the corresponding error location and the error rung will be shown in red. Modify the error.
Online to Transfer Normal online. Enables you to go online with a PLC of the device type and method specified when opening a project. This time, online/debug functions when working online with CX-Simulator are explained in this guide (Install CX- Simulator separately). The CX-Simulator Console box is shown. The background color of Ladder Window changes to gray. The operating mode of the active PLC is shown.
Online to Transfer The rungs being monitored are shown in a specified color.
Online to Transfer Move the mouse pointer to the arrow position shown in the right figure and drag the cursor down with the left mouse button pressed. The screen is divided into two panes up and down, and you can display any address in two panes respectively by using the scroll bars.
Online to Transfer Alt 3 400 You can also enter a given address in this status.
Online to Transfer 4-word data is displayed in the binary system.
Online to Transfer Click the right button of a mouse on Sheet1, and then select [Watch Sheet] -> [Rename]. Enter a name. To add a sheet, select [Watch sheet] -> [Insert].
Online to Transfer Move the mouse cursor to this position. Drag and drop on Watch Window.
Online to Transfer
Online to Transfer The count number is displayed on the dialog every time the differential condition (differential up in this example) is satisfied and the color of the box changes each time.
Online to Transfer Click the right mouse button. -> [Force] -> [On] Force Off/Cancel of bits/coils are enabled in the same way.
Online to Transfer
Online to Transfer Monitoring Alt 4 1 Enter a bit number that you want to find in the [Address] field. 2 You can also move the cursor to a bit that you want to find. 3 The found bits are listed.
Online to Transfer Online Edit Space Space Shift Space
Online to Transfer Space
Online to Transfer The contacts/coils of which annotations include the keyword entered in the Find dialog are displayed on Output Window. Double-click an item, and then the cursor moves to the applicable bit in Ladder Window.
Online to Transfer L Alt Shift R
Online to Transfer Output Window is displayed and the results are listed. Double-click an item in the list, and the cursor will go to the applicable bit.
Online to Transfer Double-click End